Raspberry Pi installation🔗
Download the VisionAppster Raspberry Pi SD card image.
Find an empty SD card and connect it to your computer (you may need an external SD card reader).
Open Etcher and select the disk image file (va-rpi-img-latest.zip) you just downloaded.
Select the SD card you wish to write your image to.
Insert the SD card into your Raspberry Pi.
Connect the power cable.
On command line🔗
The downloaded SD card image file is just a zipped disk image that you can also flash with command-line tools. The following instructions are for Linux.
To begin, you need to find out the name of your SD card device. It is
crucial to get this part right; you may wipe out your own hard drive
otherwise. Open a terminal and type
$ lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sda 8:0 0 477G 0 disk ├─sda1 8:1 0 512M 0 part /boot/efi └─sda2 8:2 0 476,4G 0 part / mmcblk0 179:0 0 7,5G 0 disk ├─mmcblk0p1 179:1 0 43,9M 0 part └─mmcblk0p2 179:2 0 7,5G 0 part
This computer has a hard drive (
sda) and an integrated SD card
reader, which shows up as
mmcblk0. The inserted SD card has two
mmcblk0p2), which are going to be
overwritten. If the same SD card is inserted using a USB card reader,
the output will look like this:
$ lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sda 8:0 0 477G 0 disk ├─sda1 8:1 0 512M 0 part /boot/efi └─sda2 8:2 0 476,4G 0 part / sdb 8:16 1 7,5G 0 disk ├─sdb1 8:17 1 43,9M 0 part └─sdb2 8:18 1 7,5G 0 part
In this case, the card is accessed through a different bus and hence
sdb as its name. The two partitions are now
To flash an SD card image, you just need to write the image file into the correct device (as root):
sudo -s unzip -p va-rpi-img-latest.zip > /dev/mmcblk0
The name of the device will be
something similar. If unsure, use Etcher.
The VisionAppster Rpi image is based on Arch Linux ARM. The default username and password are alarm and alarm, respectively. The system has SSH enabled. The root password is root.
Finding out the IP address of the RPi may be a bit tricky. If you have display and keyboard connected to the RPi, open a terminal and type the following command:
In the output, look for lines like this:
inet 192.168.1.92/24 brd 192.168.1.255 scope global eth0
Here, 192.168.1.92 is the IP address.
eth0 identifies a wired
interface. You can modify the network configuration on the RPi using
raspi-config. If you do and connect using WiFi, look for
in the output of the
ip a command.
If you are running the RPi headless, you need to have a look at your DHCP server’s log files to find out which IP address was assigned to the RPi.
If you can’t access the DHCP log file but you know the network segment to which you attached the RPi, you may try nmap. On Linux, you can usually install it using your system’s package manager (e.g. apt or yum). A Windows installer is available on the nmap site.
On Linux, give the following command (
sudo is needed to display MAC
addresses, which reveal the network card manufacturer):
sudo nmap -sn 192.168.1.0/24
On Windows, open a command prompt as administrator and type:
nmap -sn 192.168.1.0/24
Here, 192.168.1.0/24 is your network segment, which you need to find out
e.g. by using
ip a or by opening the IPv4 properties of your network
interface in a graphical environment.
Once you have found the IP address, you can test the installation by pointing your browser to http://ip-address-of-rpi:2015/. You can also add the RPi as a remote in VisionAppster Builder. This makes it possible to use the camera of the RPi as an image source in the Builder and to export packages directly to it.